绝缘电气强度击穿电压试验仪结构原理及性能特点：
1、主要由升压系统、测量系统、A/D转换器、放电系统、电极、油箱、电极定位架、计算机数据处理系统、软件等组成；
2、计算机---A/D转换器---测量控制系统---调压装置---升压变压器---试样；
3、高压变压器主要产生试样所需的直流电压；
4、调压器用于调节升压变压器输入端电压以产生高压所需的输入电压；
5、电压测量主要是从高压变压器测量端测量，高压变压器测量端和高压端是线性的；
6、放电系统在试验做完以后放电，以免产生放电对人身的危害；（当试验结束后，机器部件仍可能存在残留的高电压，此残留电压足以对人产生致命的伤害，配备此棒，完好的解决此安全隐患）。

绝缘电气强度击穿电压试验仪技术参数

1 试验变压器

1.1 输出电压： AC  0-10000V，DC 0-10000V；

1.2 输入电压：220v

1.3 额定容量下，长期连续运行；

1.4 zui大输出电压下，PD≤1pC；

1.5 噪声≤58dB（1m位置测量）。

2 调压器

2.1 输入电压：220V；

2.2 额定容量：2kVA（如果有补偿，可以小于15kVA，但不小于10kVA）；

2.3额定容量下，长期连续运行；

2.4噪声≤58dB（1m位置测量）;

2.5 电动调压。

3 高压分压器

3.1 高压臂电容：1nF；

3.2 分压比：700（可讨论，结合测量控制系统）；

3.3 额定容量下，长期连续运行；

3.4 zui大输出电压下，PD≤1pC；

3.5 测量精度：1%。

4 计算机控制

4.1 蓝牙连接；

4.2 安全保护；

5 试验电极

5.1 满足GB/T 1408-2006 绝缘材料电气强度试验方法；

5.2 满足GB/T 1695-2005 硫化橡胶工频电压击穿强度和耐压强度试验。

绝缘电气强度击穿电压试验仪适用材料：

    主要适用于固体绝缘材料如下：

电线套管、

树脂和胶、

浸渍纤维制品、

云母及其制品、

塑料薄膜、

陶瓷、

玻璃、

绝缘漆、

硫化橡胶、

电缆纸、

绝缘漆漆膜、

硬质橡胶、

纸板等绝缘介质在空气或液体介质中，测量工频（48~62Hz）或对应直流电压下击穿强度和耐电压时间。

适用于连续均匀升压或逐级升压的方式，对试样施加交流/或直流，电压直至击穿，测量击穿电压值，计算试样的击穿强度；用迅速升压的方法，将电压升到规定值，保持一定的时间试样不击穿，定此时规定值为试样的耐电压值。

绝缘电气强度击穿电压试验仪技术指标：

输入电压： 交流 220 V    输出电压： 交流 0--100 KV ;/直流 0—100 KV

电器容量： 10KVA   高压分级： 0-100KV    升压速率：0.01-5.0kv

              （备注：满足标准要求并可以根据用户需求设定不同的升压速率）

06、试验方式： 交流试验/ 直流试验：1、匀速升压  2、梯度升压 3、耐压试验

试验介质：空气，试验油    安装灵敏度较高的过电流保护装置保证试样击穿时在0.05S内切断电源。    仪器配备先进的故障报警系统 避免用户操作故障仪器发生危险。（上位机报警和下位机报警）

绝缘电气强度击穿电压试验仪

使电介质击穿的电压。电介质在足够强的电场作用下将失去其介电性能成为导体,称为电介质击穿,所对应的电压称为击穿电压。

电介质击穿时的电场强度叫击穿场强。不同电介质在相同温度下,其击穿场强不同。当电容器介质和两极板的距离d一定后,由U1-U2=Ed知,击穿场强决定了击穿电压。击穿场强通常又称为电介质的介电强度。

提高电容器的耐压能力起关键作用的是电介质的介电强度。附表为各种电介质的相对介电常量εr和介电强度。电介质εr击穿场强,×106/（V·m-1）

Breakdown voltage insulation dielectric strength tester structure principles and performance characteristics:
1, mainly by the booster system, measuring system, A/D converter, discharge system, electrode, fuel tanks, electrode positioning, computer data processing system, software, etc;
2 - A/D converter, computer measurement control system - - - - regulating device step-up transformer - sample;
3, high voltage transformer is mainly produce samples required dc voltage;
4, voltage regulator is used to adjust the step-up transformer voltage of the input to generate the input voltage to high voltage;
5, voltage measurement mainly from high voltage transformer end measurement, high voltage transformer is linear measurement end and high end;
6 finish after discharge, discharge system in the test, lest produce discharge of bodily harm; (when the experiment ended, the machine parts are still there may be residual high voltage, the residual voltage is enough to cause fatal damage to people, equipped with the rod, solve the potential safety hazard of intact).
 
 
 
 
 
 
Insulation dielectric strength tester breakdown voltage technology parameters
 
1 testing transformer
 
Output voltage: 1.1 AC 0-10000 - v, DC 0-10000 - v;
 
1.2 the input voltage: 220 v
 
1.3 under the rated capacity, long-term continuous operation;
 
1.4 under the maximum output voltage, PD 1 PC or less;
 
1.5 noise 58 db (1 m position measurement) or less.
 
2 voltage regulator
 
2.1 the input voltage: 220 v;
 
2.2 nominal capacity: 2 kva, if any compensation, can be less than 15 kva, but not less than 10 kva);
 
2.3 under the rated capacity, long-term continuous operation;
 
2.4 noise acuities were 58 db (1 m position measurement);
 
2.5 the electric voltage regulation.
 
3 high voltage divider
 
3.1 high pressure arm capacitance: 1 nf;
 
3.2 compression ratio: 700 (can be discussed, combined with measuring control system);
 
3.3 under the rated capacity, long-term continuous operation;
 
3.4 under the maximum output voltage, PD 1 PC or less;
 
3.5 accuracy: 1%.
 
The computer control
 
4.1 bluetooth connection;
 
4.2 safety protection;
 
5 test electrode
 
5.1 meet the GB/T 1408-2006 insulation dielectric strength test method;
 
5.2 meet the GB/T 1695-2005 rubber power frequency voltage breakdown strength and compression strength test.
 
 
 
 
 
 
 
 
Insulation dielectric strength tester breakdown voltage applicable materials:
 
Mainly suitable for solid insulating material is as follows:
 
The wire casing,
 
Resin and rubber,
 
Impregnated fiber products,
 
Mica and its products,
 
Plastic film,
 
Ceramics,
 
Glass,
 
Insulating paint,
 
Vulcanized rubber,
 
Cable paper,
 
Insulating varnish film,
 
Hard rubber,
 
Cardboard in air or fluid medium, such as insulating medium measuring power frequency (48 ~ 62 hz) or the corresponding breakdown strength under dc voltage and voltage withstand time.
 
 
 
Apply continuous uniform booster or booster way, step by step toward a sample dc, ac/or until the breakdown voltage, breakdown voltage measurement, calculation of sample breakdown strength; Use the method of rapid booster, e., will increase the voltage to maintain a certain amount of time the sample breakdown, not set the withstand voltage value of the specified value for sample and now.
 
 
 
 
 
 
 
 
 
Insulation dielectric strength tester breakdown voltage technical indicators:
 
The input voltage: ac 220 V output voltage: communication 0-100 KV; / dc 0-100 KV
 
Electric capacity: 10 kva high-pressure sizing: 0-100 kv step-up rate: 0.01 to 5.0 kv
 
(note: meet the standard requirements and can be set according to user requirements of different rate of pressure rise)
 
06, test method: ac/dc test: 1, 2, gradient booster 3 uniform booster, withstand voltage test
 
Test medium: air, oil test installation high sensitivity of over current protection device to ensure the sample breakdown within 0.05 S when cut off power supply. The instrument is equipped with advanced fault alarm system Avoid user operation fault instrument. Alarm (the upper machine and lower machine alarm)
 
 
 
 
 
 
 
 
 
 
Insulation dielectric strength tester breakdown voltage
 
The dielectric breakdown voltage. Dielectric under the action of electric field in a strong enough will lose its dielectric properties become the conductor, called the dielectric breakdown, the corresponding voltage is called the breakdown voltage.
 
When the dielectric breakdown electric field intensity is called breakdown voltage. Different dielectric under the same temperature, the breakdown voltage is different. Capacitor medium and the plates, after a certain distance d by U1 - U2 = Ed, breakdown voltage determines the breakdown voltage. Dielectric breakdown voltage is often called the dielectric.
 
Increase the ability of condenser pressure is dielectric plays the key role of dielectric strength. Schedule for all kinds of dielectric epsilon r relative dielectric constants and dielectric strength. Dielectric breakdown field strength epsilon r, x 106 / (v. m - 1)